Demo site by Demand & ConvertWant a website like this? Get a free website + a 60-day free Local SEO trial.Get my free website

Category: Uncategorized

How to Measure a Room for New Flooring

Measuring a room for flooring is not hard, and it helps you plan. You will have a rough idea of how much material you need, and you can compare products on the same footing. Here is how to do it with a tape measure, paper and a pencil.

What you need

  • A tape measure long enough to cross the room
  • Paper and a pencil, or graph paper if you have it
  • A calculator
  • A second person to hold the tape, if you can find one

Draw the room first

Sketch the shape of the room from above. It does not need to be to scale. Mark doors, closets, a fireplace, kitchen cabinets and anything else fixed to the floor. You will write each measurement on this sketch, which makes mistakes much easier to spot.

Measure a simple rectangle

Measure the length of the room along one wall, from wall to wall, not from baseboard to baseboard. Then measure the width. Multiply the two numbers to get the area.

For example, a room that is 12 feet long and 10 feet wide has an area of 120 square feet.

Measure each wall in two places if you can. Walls are often not quite parallel, and you should use the larger number.

Break an odd room into rectangles

Many rooms are L-shaped or have a bump out for a bay window or a closet. Split the sketch into rectangles with dotted lines. Measure each one, work out its area and add them together.

Say the main part of a room is 12 feet by 10 feet, and a closet off it is 6 feet by 2 feet. That is 120 square feet plus 12 square feet, or 132 square feet in all.

Do not forget the small spaces

  • Closets, if the floor will run into them
  • Doorways, where the floor continues to the middle of the door
  • Hallways that connect the rooms
  • The space under a refrigerator or a range, which usually gets flooring too

Flooring does not normally go under fixed kitchen cabinets, so leave those areas out.

Feet and inches

Mixing feet and inches is the most common source of errors. Pick one way and stick to it. An easy method is to round each measurement up to the next half foot. A wall that is 11 feet 4 inches becomes 11.5 feet. Rounding up gives you a small cushion.

Allow for cuts

You will need more flooring than the bare area. Planks are cut at the walls and around doorways, and some of the offcuts cannot be used. A room with many corners or a floor laid on a diagonal wastes more than a plain rectangle laid straight. The product instructions usually say how much extra to allow.

Flooring is sold by the box, and each box covers a set area. Divide your total, with the extra, by the coverage per box and round up to a full box.

Stairs are measured differently

Stairs are counted, not measured by area. Count the steps, then measure the width of a step, the depth of the tread and the height of the riser. Note any steps that are wider or curved, and any landings, which are measured as small rooms.

Things to note besides size

While you have the tape out, write down a few more details. They affect the job as much as the area does.

  • What the floor is now, and how many layers you can see at a floor vent or a doorway
  • Whether the room is on a concrete slab, over a basement or over a crawl space
  • The floors in the next rooms and whether they are higher or lower
  • Doors that swing over the floor and may need trimming
  • Any spots that squeak, dip or feel soft

When to have a pro measure

Your own measurements are good for planning and for comparing products. Before any flooring is ordered, have the installer measure. They will check the same things again, plan the layout and take responsibility for the amount ordered.

Roomview Floors measures in person on every job. Call or send a request and we will bring samples at the same visit.

How to Test Flooring Samples in Your Own Room

A flooring sample can look perfect in a store and wrong in your living room. The sample did not change. The light, the walls and everything around it did. Here is how to test samples at home so you can choose with confidence.

Get the biggest sample you can

A small square shows you the color and not much else. Wood and wood-look floors vary from plank to plank, with knots, grain and lighter and darker boards. Ask for full planks, and for more than one of each floor. Three or four planks side by side show you the range you will see across a room.

Put the samples on the floor

It is tempting to hold a sample up or prop it on a counter. Floors are seen from above and at a low angle, so lay the planks flat on the floor where they will go. Push them together the way they would be installed.

Look at them at different times of day

Light changes color more than most people expect.

  • Morning and evening sun is warm and brings out red and yellow tones.
  • Midday light is cooler and shows the floor closer to its true color.
  • Lamps and ceiling lights at night can make a gray floor look flat or a warm floor look orange.

Leave the samples down for a couple of days and look at them each time you pass.

Check them against what is staying

A floor does not sit alone. Move the samples next to the things that are not changing:

  • Kitchen cabinets and counters
  • Baseboards, door frames and stair rails
  • A brick or stone fireplace
  • Large furniture and rugs
  • The floor in the next room, where the two will meet

You are looking for a floor that gets along with these, not one that matches them exactly. A floor a few shades lighter or darker than wood cabinets often looks better than a near match.

Stand back and walk past

Look at the samples from the doorway, which is how you will first see the room. Then walk past them. Note how much the pattern stands out from a distance. A floor with strong grain or a lot of color change can look busy across a large room and lively in a small one.

Do a few real-life tests

  • Sprinkle a little dust or a few crumbs on each sample. Very dark and very light floors both show more.
  • If you have a pet, see how its hair shows up.
  • Run a fingernail lightly across the surface to feel the texture and see how it marks.
  • Step on it with socks and with shoes. Some finishes feel smoother than others.
  • Look at the sheen with a window behind it. A glossy floor shows footprints and scratches more than a matte one.

Narrow it to two

Too many choices make it harder, not easier. Rule out the ones that are clearly wrong on the first day. Keep two finalists and live with them a little longer. Most people find that one of them starts to feel like part of the room.

Ask the practical questions

Before you settle, check that the floor suits the room and not just your eye.

  • Can this product handle the moisture in a kitchen, a bath or a room over a crawl space?
  • What does it need under it?
  • How thick is it, and how will it meet the floors in the next rooms?
  • How is it cleaned?

Take a photo, but trust your eyes

Photos are handy for comparing later, but phone cameras shift color. Use them as notes. Make the decision standing in the room.

If you would like help, call Roomview Floors. We bring full-size planks to your home, lay them out with you and measure the rooms while we are there.

Not sure which floor fits your room?

Tell us about the room and we will bring samples you can lay on your own floor.

Book a Free Measure(804) 555-0131 or send us the details
Call